Chauvet COLORado 1 tour Manuale Utente

SnapshotOK on DimmerOutdoor OK Sound Activated DMX512Master/Slave115V/230V SwitchReplaceable Fuse User Serviceable Duty Cycle COLORado™ 1USER MANUAL C

4. OPERATING INSTRUCTIONSNavigating the Control Panel Access control panel functions using the four panel buttons located directly underneath the LCD

Menu MapAUTOWhen navigating the menu:Use the “UP” button to move up. Use the “DOWN” button to move down.Use the “SET” button to move right. Use the “M

Menu FunctionsMENUOPTIONDESCRIPTIONAUTOAuto Mode – Master Unit: Sets the fixture to Master status forMaster-Slave operation and the built in programs

UPLOAD CUSTOM PROGRAMS TO ANOTHER FIXTURE:1) On all fixtures that are going to receive the custom programs from the source unit, set them for DMX oper

Master/Slave Mode:This mode will allow you to link up to 32 units together without a controller.1) Use standard DMX cables to daisy chain your units t

Example ConfigurationsID Address: 01ID Address: 02 ID Address: 03 ID Address: 04ID Address: 05ID Address: 06The figure above shows 6 fixtures connecte

DMX Channel Values (ARC Mode)CHANNEL VALUE FUNCTION1000 255 Red (or step time when PR. 01 – PR. 10 is activated)0 – 100%2000 255 Green (or fade time w

128 191 192 255 Color changing pulse with fadeout (slow > fast) Color changing pulse with fade-in/out (slow > fast) 7000 009 010 019 020 029

232233234235236237238239240241242243244245246247248249250251252253254255ID 43 ID 44 ID 45 ID 46 ID 47 ID 48 ID 49 ID 50 ID 51 ID 52 ID 53 ID 54 ID 55

5. COLORADO™CONTROLLEROverviewLCD Display PanelMODE SETUP UP DOWNMODE Accesses main menu or backs out of sub-menuSETUP Selects the currently displayed

TABLE OF CONTENTS1. BEFORE YOU BEGIN...

Menu MapMAINFUNCTIONSELECTION SELECTION SELECTION SELECTIONStep time[001] [255]WashprogramWash [1]Wash [8]EditFade time[001] [255]EffectprogramEffect

Custom Program1) Select from the eight existing [Custom] programs and it will instantly play.2) Enter the [Edit] section to create or edit program.3)

[Reset to factory settings]This function will reset all the settings to the factory defaults except for [Custom] programs.Factory Default SettingsSett

191 210 211 220 221 255 Effect [7] BlackoutEffect [8] 3000 010 011 030 031 040 041 060 061 070 071 090 091 100 101 120 121 130 131 150 151 16016

General TroubleshootingApplies toSymptom Solution(s)LightsFoggers&SnowControllersDimmers&ChaserAuto shut off Check fan thermal switch resetBea

Technical Support Address: Service Dept.3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.)Support (Email): [email protected]: (954) 929-1115

PhotometricsWHITE123012320.5241.0561.57102.60Diameter (m)2750700 320 190 145 LU X51RED123012320.5241.0561.57102.601145290 130 72 50 LUX51GREEN12301232

General MaintenanceTo maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usageand environment are contributing fac

COLORado 1 User Manual 28 2008-01-18/16:45Technical SpecificationsWEIGHT & DIMENSIONSLength...

1. BEFORE YOU BEGINWhat is included ¾ 1 x COLORado™ 1 ¾ 1 x Power cable with plug ¾ 1 x IP65 power extension cable ¾ 1 x IP65 signal extension cab

Safety Instructions Please read these instructions carefully, which includes important information about the installation, usage and maintenance of th

DMX Channel Summary CHANNEL FUNCTION1Master Dimmer 2Red3Green4BlueMaster Dimmer RedGreenBlue5Color Macros 6Strobe7Auto/Custom Programs8ID Address9Inst

Product Overview Power In ConnectorPower Out ConnectorDMX In ConnectorDMX Out ConnectorControlPanelHangingBracket Gel frame (optionalaccessory) Tilt A

3. SETUPDisconnect the power cord before replacing a fuse and always replace with the same type fuse. Fuse Replacement The fuse for this fixture is lo

CABLE CONNECTORSCABLE CONNECTORSCabling must have a male XLR connector on one end and a female XLR connector on the other end.Cabling must have a male

Master/Slave Fixture Linking 1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first fixture.